Home » Posts tagged 'emergency plumbers'

Tag Archives: emergency plumbers

Plumber Tips for Fixing Plumbing Problems in the Laundry Room

Plumbing is a skillful profession that requires a lot of training and experience. It is a trade that many people choose after completing a high school diploma program or apprenticeship and obtaining a license from the local jurisdiction.


Plumber In Glendora is responsible for installing and connecting pipes, fixtures, and appliances. They also inspect their work for compliance with building codes and regulations. They need good customer service skills because they interact with clients regularly.

The washer on the faucet seat, or valve stem, wears out and needs to be replaced. A plumber can dress it using a seat-dressing tool, which has square and hexagonal heads to fit most faucets. You can also replace the washer, but this requires removing the stem from the counter top, so it’s not usually practical unless you have easy access to the area beneath the sink. Coat new washers with plumber’s grease to help them last longer.

Remove the Stem

When installing a new stem, use caution when threading it on the bar to avoid damaging the steerer tube or the seat post. A wrench is recommended for this step to help you grip the stem securely and apply even pressure.

Once the new stem is installed, reinstall the face plate and tighten the bolts in an X pattern. Some stems require a certain amount of insertion before they will begin to rotate freely in the quill. Consult the manufacturer’s documentation for this information.

An experienced plumber can help you install or replace a faucet stem. However, doing it yourself can save you money and gives you the satisfaction of a successful DIY project. You can also prevent costly repairs by repairing or replacing a faulty faucet stem before it becomes damaged.

Remove the Packing Nut

Often the culprit of leaky shutoff valves is loosening of the packing nut, which seals around the stem. If you turn off the water using the appropriate shut-off valve and tighten this large flat nut slightly (with a wrench) with some penetrating oil like Liquid Wrench, you may be able to stop the leak.

However, be sure to apply gentle even pressure, never brute force or a sudden burst of power. This simple repair usually takes just a few minutes from start to finish and is a satisfying little fix for plumbers.

If this doesn’t stop the leak, you will likely need to replace the packing material. This is easily done with readily available Teflon wrapping material that comes in stringlike form. The new packing material is wrapped around the stem, then the packing nut is tightened.

Remove the Screw

Corroded screws and screw heads that are stripped can be difficult to remove. You can use Kroil or another penetrating oil to loosen them. Alternatively, you can also drill past the head of the screw with the next size up bit. The screw should then easily pull out. You may need to repeat this step if the screw is really stuck or rusted in place. This is a quick and easy task that most plumbers can do for you, but you can do it yourself in only a few minutes.

Replace the Washer

If your washer is leaking, you may be in need of a plumber. In the laundry room, leaks can lead to water pooling on the floor, which can cause paint flaking, mildew, and other damage. If this occurs, it’s important to act quickly.

If you’re in need of a plumbing repair, turn off the water supply to the sink (there should be an isolation valve underneath the faucet). Then, undo the handle and remove the washer.

While CR members completed 53 percent of their washing machine repairs themselves, we don’t recommend trying to fix a washer yourself unless you’re quite handy and the problem is minor, like replacing a button or cleaning a filter. A major problem could require a new motor, and that can be expensive. Also, if your washer is older and you’re doing multiple loads of laundry each day, it may be more cost-effective to buy a new one.

Replace the Seat Washer

The washer on the valve seat that the stem pushes against can wear out and not provide a tight seal, leading to leaks. Replacing the washer should stop the drips. If it doesn’t, the seat itself may be corroded or pitted and will need to be replaced. Some faucet seats are replaceable; others can be “dressed” by grinding them down with a special tool to provide a new surface for the washer to seal on.

A round, recessed washer sits beneath the stem and is held in place by a flat, domed retainer ring that’s typically attached to the handle. Examine both of these to ensure they are intact. Coat the retainer ring and the new washer with nontoxic plumber’s grease to make sure they don’t leak.

Replace the Stem

After shutting off the water and removing the handle, remove the old stem. You should be able to unscrew it with the Allen wrench or Phillips-head screwdriver and set it aside. You may have a decorative cap covering the valve stem assembly screw; remove this with a flat-head screwdriver or edge of utility knife and screw it off. Replace the valve stem with a new one of the same size and coat it with food-safe plumber’s grease.

If your new stem has a different stack height from the old one, you will need to rearrange the spacers on top of the steerer tube to match. This is not a safety issue but it will affect your comfort and control. It’s important that your bicycle fit is comfortable and appropriate for you!

Replace the Packing Nut

A professional plumber may use a different name for this nut (often called a stuffing nut) but the function is the same. If this is the source of your faucet leak it will need to be replaced. Again, be sure to turn off the water before working on this part of the faucet. Use a wrench appropriately sized for this tight nut, and only turn it a few turns to start with. Never over-tighten this nut!

This is a quick and easy repair that will stop drips, in most cases. In fact, it is the first step many homeowners will take before calling a plumber. It’s a little tricky because you must have the proper tools and the right touch but it is something almost anyone can do. Just be sure to shut off the water to the valve until you finish this job!

Replace the Screw

Generally, plumbers use their skills to maintain plumbing systems that facilitate water, gas and waste removal in residential and commercial buildings. They often work with architects and construction teams to design plumbing infrastructure for new building projects, and they can also troubleshoot existing systems to repair leaks or other problems.

Plumbers must have excellent analytical and problem-solving abilities to effectively assess and remedy issues. They must also have a strong mechanical aptitude and understand the science behind water flow to make informed decisions when working with pipes, fixtures and appliances.

To become a plumber, you can pursue a formal apprenticeship, which typically lasts four to five years and includes classroom instruction and paid on-the-job training. Alternatively, you can attend a vocational school or trade program to learn the basics of plumbing installation and repair. A high school diploma is usually required for both options.